macdrivermuseum.net

home *** CD-ROM | disk | FTP | other *** search

/ macdrivermuseum.net / www.macdrivermuseum.net.tar / www.macdrivermuseum.net / nic / daynaccard121.sit / communicard installer 1.2.1 mac / CommuniCard Installer 1.2.1 / Modem Documentation / ARA folder / Dayna CommuniCard_C < prev next >

Wrap

Text File | 1995-10-11 | 8KB | 367 lines

! Dayna CommuniCard 1.1 ! ! 'mlts' resource info for this modem: ! byte 1 == 01 -> modem HAS builtin reliability protocols ! byte 2 == 00 -> reserved by Apple ! byte 3 == FF -> max hex chars in varstr 7 (255 dec) ! byte 4 == 00 -> max hex chars in varstr 8 ! byte 5 == 00 -> max hex chars in varstr 9 ! @ORIGINATE @ANSWER ! ! Set up the modem - label range is 1-10 ! ! Mac talks to the modem at 38,400 bps. serreset 38400, 0, 8, 1 ! ! reset the serial port handshake options HSReset 0 1 0 0 0 0 ! settries 0 @LABEL 1 flush matchclr matchstr 1 3 "OK\13\10" ! &F - recall factory settings ! &K3 - Enable CTS/RTS Hardware flow control (Set by AT&F) ! W2 - gives Connect with DTE result codes ! X4 - Use extended result codes (Set by AT&F) ! &Q6 - Disable auto port rate adjust ! &Q6 - Use asynch mode (no reliability protocols) (Same as above) ! S46=136 - No compression ! Y1 - Disconnect on Long Break ! S7=60 - To allow for an international call ! S0=0 - Don't answer calls (Set by AT&F) ! E0 - Turn command echo off write "AT&FE0W2&Q6Y1S7=60S46=136\13" matchread 30 inctries iftries 2 71 ! Modem not responding, send long break. LBreak jump 1 ! @LABEL 3 ! Modem responding & configured. ! Determine if reliable link is requested. ! ! If modem mnp10 link requested (var 4 == 2) then jump label 4 ! If modem v42 link requested (var 4 == 1) then jump label 5 ! If no modem v42 link requested (var 4 == 0) [same as ARA 1.0] then jump label 9 ! ifstr 4 4 "2" ifstr 4 5 "1" ifstr 4 9 "0" ! ! Else invalid value in var 4, exit with error jump 76 ! @LABEL 4 ! MNP10 reliable modem link is requested ! matchclr matchstr 1 7 "OK\13\10" ! \N2 - MNP reliable mode ! -K1 - enables V.42 LAPM to MNP10 conversion ! )M1 - enable power level adjustment ! *H1 - link negotiation occurs at 1200 write "AT\\N2-K1)M1*H1\13" matchread 300 jump 71 ! @LABEL 5 ! Reliable link is requested. OK for LAP-M -> MNP 4. matchclr matchstr 1 7 "OK\13\10" ! W2 - gives Connect with DTE result codes ! &Q5 - v42 autoreliable mode ! S48=7 - Protocol negotiation on ! S36=7 - LAPM, then MNP4, then Asynch with constant DTE speed ! S46=136 - Compression (LZW/v42bis, MNP 5, ATC) disabled write "ATW2&Q5S48=7S36=7S46=136\13" matchread 300 jump 71 ! @LABEL 7 ! If we DID support v42b in the modem, this is where it would go. ! @LABEL 9 ! If speaker on flag is true, jump to label 13. Else turn off the speaker. ifstr 2 13 "1" pause 5 matchclr matchstr 1 13 "OK\13\10" write "ATM0\13" matchread 30 jump 71 ! ! Modem ready, so enable answer or dial mode - label range is 11-30 ! Determine if answer or originate mode. ! @LABEL 13 pause 5 ifANSWER 62 ! ! Dial type dispatch ! ! Normal dialing (parm 6 == 0) jump to 19 ! Blind dialing (parm 6 == 1) jump to 17 ! Manual dialing (parm 6 == 2) jump to 15 ! ifstr 6 19 "0" ifstr 6 17 "1" ifstr 6 15 "2" ! ! Else invalid value in var 6, exit with error jump 76 ! @label 15 note "Manual dialing initiated..." 3 ! X1 - ignore dialtone and busy for manual dialing, D to dial write "ATX1D \13" jump 32 ! @label 17 note "Dialing without dialtone." 3 matchclr matchstr 1 19 "OK\13\10" ! X3 - ignore dialtone but report busy for blind dialing write "ATX3\13" matchread 30 jump 71 ! ! This is where we break up long dialstrings. ! This modem has a 255 chars command buffer and dial string ! fragmentation is not supported by Hayes. ! Labels 19 - 27 reserved. ! @label 19 ! Parameter 1 contains the full dialstring from the connection document. ! Parameter 3 contains "P" for pulse & "T" for tone dialing. ! Parameter 7, 8 & 9 contain the dial string fragments. ! note "Dialing ^1." 3 write "ATD^3^7\13" jump 32 ! ! Connecting - label range is 31-60 ! @LABEL 32 matchclr ! matchstr 1 68 "RING\13\10" matchstr 2 72 "NO DIALTONE\13\10" matchstr 3 73 "NO CARRIER\13\10" matchstr 4 73 "ERROR\13\10" matchstr 5 74 "BUSY\13\10" matchstr 6 75 "NO ANSWER\13\10" ! matchstr 7 34 "CONNECT 1200\13\10" matchstr 8 34 "CONNECT 1200/REL\13\10" matchstr 9 35 "CONNECT 2400\13\10" matchstr 10 35 "CONNECT 2400/REL\13\10" matchstr 11 36 "CONNECT 4800\13\10" matchstr 12 36 "CONNECT 4800/REL\13\10" matchstr 13 37 "CONNECT 7200\13\10" matchstr 14 37 "CONNECT 7200/REL\13\10" matchstr 15 38 "CONNECT 9600\13\10" matchstr 16 38 "CONNECT 9600/REL\13\10" matchstr 17 39 "CONNECT 12000\13\10" matchstr 18 39 "CONNECT 12000/REL\13\10" matchstr 19 40 "CONNECT 14400\13\10" matchstr 20 40 "CONNECT 14400/REL\13\10" matchstr 21 41 "CONNECT 16800\13\10" matchstr 22 41 "CONNECT 16800/REL\13\10" matchstr 23 42 "CONNECT 19200\13\10" matchstr 24 42 "CONNECT 19200/REL\13\10" matchstr 25 43 "CONNECT 21600\13\10" matchstr 26 43 "CONNECT 21600/REL\13\10" matchstr 27 44 "CONNECT 24000\13\10" matchstr 28 44 "CONNECT 24000/REL\13\10" matchstr 29 45 "CONNECT 26400\13\10" matchstr 30 45 "CONNECT 26400/REL\13\10" matchstr 31 46 "CONNECT 28800\13\10" matchstr 32 46 "CONNECT 28800/REL\13\10" ! matchread 700 ! If in ANSWER mode, loop back. ! Else in ORIGINATE mode, the modem has timed out. ifANSWER 32 jump 71 ! ! This modem has been setup to do CTS handshaking, ! and we assume that a CTS handshaking cable is being used, ! so we leave the serial port set to 38400 bps. ! @LABEL 34 note "Communicating at 1200 bps." 2 CommunicatingAt 1200 jump 58 ! @LABEL 35 note "Communicating at 2400 bps." 2 CommunicatingAt 2400 jump 58 ! @LABEL 36 note "Communicating at 4800 bps." 2 CommunicatingAt 4800 jump 58 ! @LABEL 37 note "Communicating at 7200 bps." 2 CommunicatingAt 7200 jump 58 ! @LABEL 38 note "Communicating at 9600 bps." 2 CommunicatingAt 9600 jump 58 ! @LABEL 39 note "Communicating at 12000 bps." 2 CommunicatingAt 12000 jump 58 ! @LABEL 40 note "Communicating at 14400 bps." 2 CommunicatingAt 14400 jump 58 ! @LABEL 41 note "Communicating at 16800 bps." 2 CommunicatingAt 16800 jump 58 ! @LABEL 42 note "Communicating at 19200 bps." 2 CommunicatingAt 19200 jump 58 ! @LABEL 43 note "Communicating at 21600 bps." 2 CommunicatingAt 21600 jump 58 ! @LABEL 44 note "Communicating at 24000 bps." 2 CommunicatingAt 24000 jump 58 ! @LABEL 45 note "Communicating at 26400 bps." 2 CommunicatingAt 26400 jump 58 ! @LABEL 46 note "Communicating at 28800 bps." 2 CommunicatingAt 28800 jump 58 ! @LABEL 58 ! Add 5 second delay to insure compatibility with ARA 2.0.1. ! Each unit in the CCL is 1/10th of a second. pause 50 ! ifANSWER 59 pause 30 ! @LABEL 59 exit 0 ! ! @ANSWER ! Set the modem to answer on 1st ring - label range is 61-70 ! @LABEL 62 matchclr ! On match jump to MODEM STATUS and wait for RING matchstr 1 32 "OK\13\10" write "ATS0=1\13" matchread 30 jump 71 ! ! RING entry point ! If ORIGINATE mode return to waiting for input. ! Else claim the serial port and return. ! @LABEL 68 ifORIGINATE 32 userhook 1 note "Answering call..." 2 jump 32 ! ! Error messages - label range is 71-100 ! ! Modem Not Responding @LABEL 71 exit -6019 ! ! No Dialtone @LABEL 72 exit -6020 ! ! No Carrier or Error @LABEL 73 exit -6021 ! ! Busy @LABEL 74 exit -6022 ! ! No Answer @LABEL 75 exit -6023 ! ! Invalid Varstring Value @LABEL 76 exit -6027 ! ! Hang up the modem - label range is 101-120 ! @HANGUP ! @LABEL 102 flush settries 0 HSReset 0 1 0 0 0 0 ! @LABEL 105 ! Drop the modem into command mode with escape sequence. ! Then tell modem to hangup. ! Repeat hangup command and escape sequence 3 times max. ! flush matchclr matchstr 1 108 "OK\13\10" pause 10 write "+++" matchread 15 ! @LABEL 108 matchclr matchstr 1 111 "NO CARRIER\13\10" matchstr 2 111 "OK\13\10" matchstr 3 111 "ERROR\13\10" write "ATH0\13" matchread 30 inctries iftries 3 71 jump 105 ! ! recall the factory setting. ! @LABEL 111 pause 15 matchclr matchstr 1 114 "OK\13\10" write "AT&F\13" matchread 30 jump 71 ! @LABEL 114 exit 0 ! ! Labels 121-128 are reserved for future emergency hacks. !